Graphene oxide (GO) provides a thinner support film of higher mechanical strength, electrical and thermal conductivity compared to support films made from other materials. Agar GO support films are available on lacey carbon grids and Quantifoils.
All prices exclude VAT.
DescriptionTech Data
Product Description
Manufactured in our laboratories in Stansted using a unique application method, Agar GO support films are hydrophilic and ideally suited to imaging of small nanoparticles, nanowires and suspensions. The low atomic number and thin-layer thickness results in significantly lower background contrast than conventional supports. Agar GO support films are ideal for Cryo –TEM studies. The vitreous ice layer can be significantly thinner providing higher contrast and hence higher resolution for structural determination. GO support films can be applied to other grid sizes, material or type. Further details available on request.
Technical Data
Graphene oxide membranes are robust and almost transparent under an electron beam, making them ideal supports for the analysis of a wide range of samples by transmission electron microscopy (TEM). As produced, they are hydrophilic but this can readily be tuned as required. The graphene oxide membranes give a crystalline diffraction pattern similar to graphene and this structure acts as a convenient calibration for electron diffraction and high resolution TEM. Their ultra-low contrast makes them particularly useful for imaging small nanoparticles or nanowires whose structure is not readily resolvable on conventional carbon supports [1]. They can also be used for imaging and analysis of polymeric, macromolecular and biological samples without the need for heavy metal staining [2].
Graphene oxide support grid morphology: the graphene oxide membranes are deposited on lacey carbon supports. As figure 1 shows, monolayer graphene oxide membranes can span the holes in the lacey carbon. The graphene oxide sheets are distributed randomly across the EM grids such that some holes in the lacey carbon support are uncovered, some covered by a single monolayer of graphene oxide, and some by two or more layers of graphene oxide. On average, roughly half to three quarters of the lacey carbon holes are spanned by graphene oxide and of those roughly half are monolayer.
Structure and composition of graphene oxide: graphene oxide is composed of a graphene like sheet randomly decorated with oxygen functional groups such as epoxy and hydroxyl. Due to its graphene-like carbon backbone, apparent in the diffraction pattern shown in figure 2, graphene oxide is strong enough to span the holes in a lacey carbon support even when only a monolayer thick. The graphene oxide is synthesized from graphite powder using a modified Hummers’ method.
Use of graphene oxide grids for TEM imaging and diffraction:figure 3 shows ferritin suspended on graphene oxide, a typical example of their use as a support film [as in 1]. The ferritin was deposited from aqueous solution by placing a drop on the graphene oxide coated TEM grid and allowing it to dry. As produced, the graphene oxide is hydrophilic. However, this can readily be changed by heating in air if a hydrophobic surface is required [2]. The crystalline graphene backbone gives a characteristic diffraction pattern which can be used as a convenient calibration for the analysis of other samples either by high resolution TEM or electron diffraction [1,2].
Identifying the graphene oxide membranes: one monolayer thick the graphene oxide is almost transparent under the electron beam and so is often only apparent through wrinkles or creases in the film. Overlapping sheets are also readily visible. The most distinctive way of identifying monolayer thick regions is from the diffraction pattern: a single layer has a hexagonal diffraction pattern similar to graphene whilst multiple layers are usually in different orientations so that multiple rotationally misaligned hexagonal patterns are observed in the diffraction pattern figure 4 [1,3]. However, this can also be caused by creases in a single sheet so some care must be taken with this interpretation.
References
[1] 'Graphene Oxide: Structural Analysis and Application as a Highly Transparent Support for Electron Microscopy.' N.R. Wilson, P.A. Pandey, R. Beanland, R.J. Young, I.A. Kinloch, L. Gong, Z. Liu, K. Suenaga, J.P. Rourke, S.J. York, and J. Sloan, ACS Nano 3 (9), 2547 (2009). http://dx.doi.org/10.1021/nn900694t
[2] 'A simple approach to characterizing block copolymer assemblies: graphene oxide supports for high contrast multi-technique imaging' Joseph P. Patterson, Ana M. Sanchez, Nikos Petzetakis, Thomas P. Smart, Thomas H. Epps, III, Ian Portman, Neil R. Wilson and Rachel K. O'Reilly Soft Matter 8, 3322 (2012). http://dx.doi.org/10.1039/C2SM07040E
Image of yeast mutant ribosome suspension on GO support film courtesy of Dr Richard Collins, Single Particle EM, Faculty of Life Sciences, University of Manchester
Image of soot from engine oil on GO support film courtesy of Internal Combustion Engine Research Group (ERG) at the University of Nottingham
Delivery & Returns
LEAD TIMES: Average Lead Times are shown individually in days for any products not currently in stock. Whilst we are working closely with our suppliers to minimise the impact of global supply chain issues, and regularly update our product prices and lead times, some are subject to change due to supply chain fluctuations.
Delivery is calculated at the checkout, please see our delivery and returns page for more information.
PRICE & AVAILABILITY: Please note that while we are working closely with our suppliers to minimise any global supply chain issues, prices and availability may be subject to change at short notice.
